Problem with purg sp3 damage in raids ongoing

Toproller89Toproller89 Member Posts: 2,120 ★★★★★
in General Discussion
I’ve noticed last few raids, I’ll have all damage role charges up etc and when I hit sp3, it’s being randomly capped at just over 300k damage most of the time when it should be doing closer to 7-8mil.

This been happening for others?

Comments

  • Average_DesiAverage_Desi Member Posts: 2,666 ★★★★★
    Is it the .25% damage cap they have?
  • Average_DesiAverage_Desi Member Posts: 2,666 ★★★★★
    Have you disabled that
  • Lester_JoaoLester_Joao Member Posts: 57 ★
    My purgatory works fine 12% damage every time i use sp3...I run DOT boost.
  • PikoluPikolu Member, Guardian Posts: 8,696 Guardian
    Nightmare raids has protection built-in that gets removed when you complete missions. Gotta do that
  • Muppet17Muppet17 Member Posts: 61 ★
    Been using her this week too, no problems. Using prowess ender so the damage is capped at 4% but its working fine. Are u dropping the sp3 when shes not in rampage mode?
  • MarcB76MarcB76 Member Posts: 21 ★
    btw, does her sp3 reaching damage cap is only allowed in 1 rampage cycle? I tried 2 sp3 in 1 rampage cycle, it only reach damage cap of 4% 1x time, not the 2nd time. I'm using prowess ender
  • SirGamesBondSirGamesBond Member Posts: 7,556 ★★★★★
    edited June 11
    User issue.
    There is no bug "problem" ongoing.
  • Toproller89Toproller89 Member Posts: 2,120 ★★★★★
    SirGamesBond said:

    User issue.
    There is no bug "problem" ongoing.

    Zero solution offered, opinion rejected, thanks everyone that weighed in on it, it must be the damage cap I didn’t disable
  • BringPopcornBringPopcorn Member Posts: 9,057 ★★★★★
    Toproller89 said:

    SirGamesBond said:

    User issue.
    There is no bug "problem" ongoing.

    Zero solution offered, opinion rejected, thanks everyone that weighed in on it, it must be the damage cap I didn’t disable
    The solution offered is to disable the protection after completing a task and throwing the sp3 within the 5 second window.
    We could offer to do it for you but it breaks ToS and there is a whole mess going on.
  • Gentsy12Gentsy12 Member Posts: 175 ★★
    MarcB76 said:

    btw, does her sp3 reaching damage cap is only allowed in 1 rampage cycle? I tried 2 sp3 in 1 rampage cycle, it only reach damage cap of 4% 1x time, not the 2nd time. I'm using prowess ender

    This isn’t accurate. I used multiple sp3 in the same rampage cycle and both did the expected 4% as long as you disable the protection node again.
  • SirGamesBondSirGamesBond Member Posts: 7,556 ★★★★★
    Toproller89 said:

    SirGamesBond said:

    User issue.
    There is no bug "problem" ongoing.

    Zero solution offered, opinion rejected, thanks everyone that weighed in on it, it must be the damage cap I didn’t disable
    You thought it was an issue. It's not.
    Since the answer was already provided, there was nothing left to do then mock this ignorance.
    Only ongoing issue is Reading issue.
  • Kingering_KingKingering_King Member Posts: 1,672 ★★★★
    Lester_Joao said:

    My purgatory works fine 12% damage every time i use sp3...I run DOT boost.

    Same here, I did notice the 300k cap but other times was the full 12
Sign In or Register to comment.